aaptekgsm
A M C T

aaptekgsm

Techno Care mobile & computer technology (Training & Service)
 
HomeTop poserRegisterLog in

Attention : amct team is a subsiediary of technocare kambil.


Share | 
 

 Local mode & test mode problem, some general Info

View previous topic View next topic Go down 
AuthorMessage
AAPTEK
FOUNDER & ADMIN
FOUNDER & ADMIN
avatar

Male
Age : 60
Job/hobbies : Instructor, Programmer& Technician

PostSubject: Local mode & test mode problem, some general Info   Tue Dec 08, 2009 5:49 pm

Local mode & test mode problem, some general Info..

What is Local mode?


Local mode is triggered either by a service battery / jig from Nokia being used to power the phone,
A faulty battery, a faulty phone or the phone has got "liquid ingress” also indicate local mode in display

See this picture.





in the above picture when BSI is grounded with a resistor of
5.1k to 7k1 and insert battery, nokia sets displays local/test mode on screen

By this way we can trigger the set in to local mode and software operation through USB



Local mode is triggered for reading & writing phone pm area (EEPROM),
File system formatting etc.

What is test mode?

Test mode is for doing file system removing like full factory defaults
Also can do pm area re-writing and for unlocking the phone


Some phones displays either of these modes directly when battery is inserted to the phone
and we gets in this condition for repairing

This may be either by a faulty battery or damaged hardware in the handset.
We can assume this is a BSI related fault

TEST THE PHONE WITH A WORKING BATTERY


Now what is BSI?

BSI, the thermistor used to sense the battery temperature and shut down the charger
Their is an internal circuit from power IC to BSI lead of battery
this circuit manages charging mechanism and battery sensing.






Faulty parts in this BSI circuit may lead to the local/test mode

Or finally we have to suspect power ic


Here NOKIA 1200 schematic is used to illustrate BSI way and possible reasons for this fault.








he blue colored parts are related to the BSI function .we have to trace from battery connector, capacitors, and then other parts. These parts can be identified by reading the higher level schematic of the phone. By following this logic you may be able to trace local mode in any nokia phone

_________________
If you want to be at the HIGHEST, you must begin at the LOWEST !!
 --------------------------------------------------------
                    

Back to top Go down
http://aaptekgsm.com
SUMON1155
ADMIN & TEAM
ADMIN & TEAM
avatar

Male
Age : 32
Job/hobbies : TECHNOLOGIST

PostSubject: Re: Local mode & test mode problem, some general Info   Tue Dec 08, 2009 8:35 pm

Thankyou sir u r great.

_________________
Work For Eche Other
Back to top Go down
Tiju kkM
MODERATOR
MODERATOR
avatar

Male
Age : 32
Job/hobbies : mobile phone servicing

PostSubject: Re: Local mode & test mode problem, some general Info   Wed Dec 09, 2009 1:35 am

nice information
Back to top Go down
shamshu_knr
NO LIFE POSTER
NO LIFE POSTER
avatar

Male
Age : 27
Job/hobbies : Mobile phone Technician

PostSubject: Re: Local mode & test mode problem, some general Info   Wed Dec 09, 2009 9:10 pm

thanks
Back to top Go down
http://www.aaptekgsm.tk
MUHSIN NK
MODERATOR
MODERATOR
avatar

Male
Age : 23
Job/hobbies : TECHNICIAN

PostSubject: Re: Local mode & test mode problem, some general Info   Wed May 19, 2010 5:33 pm

thanks sir great info
Back to top Go down
Sponsored content




PostSubject: Re: Local mode & test mode problem, some general Info   

Back to top Go down
 
Local mode & test mode problem, some general Info
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» 2310 local mode done...
» Crown Lynn - Mode
» What age will my BN start breeding ? & General info ?
» Triode/Ultralinear mode switch specs?
» possible 4l60e problem?

Permissions in this forum:You cannot reply to topics in this forum
aaptekgsm :: === AMCT GENERAL FORUM SECTION === :: === OFF TOPIC ZONE ===-
Jump to: